所以要打開就很容易和底板制肘,導致刮傷
光鮮、同軸、AES數位輸入是倒過來的,拍不到也看不到
USB輸入是直立的,也很難窺知一二
另一邊應該是前級電路
![圖檔](http://i.imgur.com/tKLR1YVh.jpg)
![圖檔](http://i.imgur.com/N72GRHjh.jpg)
![圖檔](http://i.imgur.com/qaQI9tEh.jpg)
![圖檔](http://i.imgur.com/jK9Ybwvh.jpg)
![圖檔](http://i.imgur.com/khFXCiSh.jpg)
其實這個可以不用拆....
![圖檔](http://i.imgur.com/d301FZGh.jpg)
![圖檔](http://i.imgur.com/3VMzOZIh.jpg)
接地
![圖檔](http://i.imgur.com/0lwFKF1h.jpg)
側板
![圖檔](http://i.imgur.com/zKVm6yRh.jpg)
![圖檔](http://i.imgur.com/5lAIBEVh.jpg)
屏蔽
![圖檔](http://i.imgur.com/bAJZzBmh.jpg)
很多眉眉角角,最後會是L___]型,所以很容易刮傷前面板
![圖檔](http://i.imgur.com/clhGZyTh.jpg)
前面板立起來後,有些線脫落了...
![圖檔](http://i.imgur.com/DjdzGHlh.jpg)
很硬的固定線,不知道先鋒腦袋在想甚麼
![圖檔](http://i.imgur.com/KxckU7Ih.jpg)
USB部分
![圖檔](http://i.imgur.com/pWvhhtWh.jpg)
![圖檔](http://i.imgur.com/2xkl2wHh.jpg)
由左至右
CFeon EN39LV010
ISO 7640H
Winbond W9864G6JH-6
![圖檔](http://i.imgur.com/m8AeQVZh.jpg)
DA部分
![圖檔](http://i.imgur.com/tj39qwOh.jpg)
![圖檔](http://i.imgur.com/zKo5otth.jpg)
![圖檔](http://i.imgur.com/rn0TSzwh.jpg)
單聲道用上兩顆BB的OPA2134
![圖檔](http://i.imgur.com/nHKI2RNh.jpg)
55320 E018F
![圖檔](http://i.imgur.com/r3vRkoWh.jpg)
另一邊看的比較清楚
![圖檔](http://i.imgur.com/uSis5iJh.jpg)
應該是穩壓整流
![圖檔](http://i.imgur.com/ELNhm6yh.jpg)
![圖檔](http://i.imgur.com/77TeWrDh.jpg)
可以改電壓嗎?
![圖檔](http://i.imgur.com/kfMnQD5h.jpg)
沒錢,不然很想換掉 6.3A/125V
![圖檔](http://i.imgur.com/E5GJLoSh.jpg)
![圖檔](http://i.imgur.com/NBUTf72h.jpg)
排線是連接到前級放大部分
用上TOSHIBA的C3076-Y、A1241-Y
![圖檔](http://i.imgur.com/xX3RaJah.jpg)
這塊應該是前級放大?
![圖檔](http://i.imgur.com/EQFP71Dh.jpg)
![圖檔](http://i.imgur.com/YkWiap7h.jpg)
左邊那塊是數位輸入(倒過來放@@
![圖檔](http://i.imgur.com/xReLyMJh.jpg)
VR
![圖檔](http://i.imgur.com/xReLyMJh.jpg)
連接到前面板,可能是顯示器之類的?
![圖檔](http://i.imgur.com/zLpgBE5h.jpg)